Other

The Supersonic bracket (previously know as the J5) is the first and premier model of the new generation Profile Design brackets. It offers easier adjustments and a greater fit range than anything that came before it. Paring this bracket with the ergo armrest offers industry leading fit options and greater comfort. Performance The Supersonic/Ergo platform is designed to give riders the freedom to find their best possible position with a huge range of independence adjustments. Fit Data - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 58.5mm (no riser kit) to 138.5mm in 5mm increments (With aftermarket Riser Kit) - There are 80 distinct position options achievable just by moving the armrests. Combine that with risers and this bar offers 1440 possible configurations. As a clip on bar it is also possible to adjust the extension width and tilt easily. Origin - The supersonic was the first of our generation brackets - resulting from careful analysis of the way riders use their aerobars and the adjustments that need to be made. - The Ergo armrest is an integral part of the overall adjustability scheme.The dual - offset design (shared with Race and Boom armrest) gives the most precise adjustment range of any armrest on the market. This, along with the evenly curved shape, allows it to work well for the majority of riders. Extensions - Extension Shape: The 4525c extensions offer a 45 deg lower and 25 deg upper section with a 7.5mm lateral shift per side. This allows the rider to choose between a low, short reach position or a high hands, stretched position for aerodynamics. They are 400mm long and can be cut to suit nearly every rider. They are drilled for rear-exit cable routing. - Bracket: Supersonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Stack: The minimum is 58.5mm and the bracket is compatible with our existing risers which add up to 138.5mm stack with (70mm of spacers added)

The Supersonic bracket (previously know as the J5) is the first and premier model of the new generation Profile Design brackets. It offers easier adjustments and a greater fit range than anything that came before it. Paring this bracket with the ergo armrest offers industry leading fit options and greater comfort. Performance The Supersonic/Ergo platform is designed to give riders the freedom to find their best possible position with a huge range of independence adjustments. Fit Data - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 58.5mm (no riser kit) to 138.5mm in 5mm increments (With aftermarket Riser Kit) - There are 80 distinct position options achievable just by moving the armrests. Combine that with risers and this bar offers 1440 possible configurations. As a clip on bar it is also possible to adjust the extension width and tilt easily. Origin - The Supersonic was the first of our generation brackets - resulting from careful analysis of the way riders use their aerobars and the adjustments that need to be made. - The Ergo armrest is an integral part of the overall adjustability scheme. The dual - offset design (shared with Race and Boom armrest) gives the most precise adjustment range of any armrest on the market. This, along with the evenly curved shape, allows it to work well for the majority of riders. Extensions - Extension Shape: The 50c extensions offer a 50 deg ski bend shape with a 7.5mm (per side) lateral shift. This allows a neutral wrist angle with the capability to fine tune the grip width. They are 400mm long and can be cut to suit nearly every rider. They are drilled for rear-exit cable routing. - Bracket: Supersonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Stack: The minimum is 58.5mm and the bracket is compatible with our existing risers which add up to 138.5mm stack with (70mm of spacers added)

Profile's T2+ Carbon Clip-on Aerobars feature carbon ergonomic S-bend extensions with 30mm of rise for lightness, durability, and a great fit. These clip-ons also boast Profile's F-35 anatomic armrests and their J4 brackets so that you have length, width and arm adjustments for easily achieving the perfect aero tuck.

Profile Design's UCM Universal Computer Mount provides a convenient 25mm long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.

Profile Design's UCM XL Universal Computer Mount provides a convenient 60mm-long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.

Profile Design's Gap Cap works with 1" or 1 1/8" steer tubes to keep your headset adjusted properly at all times. The composite wedges are a fantastic choice for carbon steerers, and at 30-45 grams, you'll keep the front end of your bike super light.

Replace old brake barrel adjusters with a fresh pair of Problem Solvers' 10mm Brake Barrel Adjuster. Designed for use with standard brake cables.

The Problem Solvers Backstop bolts onto the frame to provide two stops for your cable housing. It's made of light, durable CNC-machined aluminum with a stainless-steel bolt, and the stops are slotted for easy cable installation/removal.

The Problem Solvers Compression Plug for 1 1/8-inch Forks is for threadless aluminum and carbon forks. It fits tightly inside the fork and provides easy headset adjustment and a nice, clean look.

Don't let chain slap damage your frame. Install a Pro Chainstay Protector. For top protection and a custom look, it's made of heavy-duty carbon-coated neoprene. Plus, it has a Velcro closure so it's easy to put on and stays in place, and it can be removed for cleaning too.

• Fits 3/8" Axles • Lightweight, compact design • Forged aluminum construction • Chromoly bolt

- AL6061-T6 alloy seatpost clamp with CNC-machined cut-outs - Rounded edges and floating bolt/ovalized hole design protects carbon frames and seatposts - 29.8mm for 27.2mm seatpost and chromoly frame - 31.8mm for 27.2mm seatpost and aluminum frame - 34.9mm for 30.9mm seatpost and aluminum frame, or 31.6mm seatpost and carbon frame - 16mm height

Origin-8's Grip N Seal QR Seat Clamp is forged from light and durable aluminum and features a rubber weather seal and an anodized finish to prevent corrosion. Its high-leverage quick-release lever makes it easy to raise/lower your seat.

- Replaces existing top cap, and allows the use of a bottle cap as a decorative cover - Compatible with both twist off and crimped style bottle caps - Bottle cap is held in place by two strong magnets - Easy to switch out bottle caps - AL6061 alloy cap and AL7075 alloy bolt

- Converts a cassette hub to a single speed - 8 spacers included in various sizes to adjust chain line - Available in black or red anodized 6061 aluminum - Fits Shimano style cassette bodies - Conical spacers for increased cog stiffness

- Top lock nut for threaded headsets - Includes water seal - Bag of 10 Lock Nuts

- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool

- Missing links to make chain installation, maintenance and reparation easier - Reusable up to 3 times - Compatible with 6, 7 and 8 speed IG drivetrains - Pin width: 7.1mm - Card of 2

FSA Compression Plugs are top assemblies for carbon steerers. Replaces the traditional top cap assembly. Includes cap, bolt, and expander. - Includes cap, bolt and expander - Top assembly for carbon steerers replaces traditional top cap and star nut assembly

FSA Standard Headset Bearings

FSA bearings that set directly into the frame without the use of pressed in cups. - 36/45 degrees is Cane Creek-compatible - 45/45 degrees is Campagnolo-compatible

This is a MegaExo Left Crank Bolt for 19mm MegaExo Cranks. - M12 bolt

Rebuild seal kits for Fox rear suspension service and repair. - Includes parts needed for rebuild

- Grade 10 chromium steel balls

- Grade 10 chromium steel balls

Cannondale Headshok/Lefty Bearing

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- Clamps to a threadless steerer, offers up to 3-1/4" stem height increase - Forged 6061 aluminum - Threaded alloy top cap

- Clamps to a threadless steerer - Offers up to 4-1/2" stem height increase - Forged 6061-aluminum provides extra strength - Machined aluminum top cap is threaded, providing easy installation

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 6802 Bearing

Campagnolo Headset Bearings

- Aheadset preload adjusting bolt

Keep the weight down and your headset snug with the Specialzied Carbon Steerer Tube Plug.

Mate Specialized's Clip-On Clamp to a pair of aero extension bars and get time on your side. Their 22.2mm diameter is compatible with many standard aftermarket extensions, and with a one-bolt hinge system, they're simple to install.

The SRL lever gives riders with 1x drivetrains the option to control their Command Post with lever option that mounts beneath the bar in place of a front shifter. - Command Post lever for the modern 1x drivetrain systems. - Adjustable lever position allows for the perfect set up. - Sealed cartridge bearing pivot for smooth action. - Ideal pull ratio for easy lever activation. - Requires additional mounting hardware (SRAM MatchMaker or equivalent is recommended).

The Command Post SRL Clamp moves the Command Post's lever into the position where the front shifter would normally go, giving you more control. - Hinge clamp for easy installation. - Lightweight alloy clamp with steel bolt. - Lightweight alloy clamp with steel bolt.

These simple rear pegs are the easiest solution for passenger footrests. XL 100mm length is large enough for passenger feet of all sizes. **For Globe Haul ST bike customers: Use of compatible (1) footrests (pegs), (2) passenger seat, (3) passenger handlebar, and (4) rear wheel cover required to safely carry passengers. All items available separately. ** - Designed for frictionless compatibility with the Haul ST and up to 2 pairs on Haul LT. - 100mm long. - Installation requires tools (not included). *Not compatible with Rear Pannier adapters on the Haul ST due to shared mounting location.

An essential part of any passenger-carrying system is something they can hold for balance. The Globe Passenger Handlebar bolts to the top of the Haul rear racks to provide passengers of all ages with a comfortable and safe grip. The reversible and versatile design can be mounted anywhere along the rack for a fully customizable setup. **For Globe Haul ST: Use of compatible (1) footrests (pegs), (2) passenger seat, (3) passenger handlebar, and (4) rear wheel cover required to safely carry passengers. All items available separately. ** - Designed for frictionless compatibility with the Globe Haul ST and Haul LT. - All tools required for assembly are included with the purchase of the Haul ST or Haul LT bike.

This soft foam pad provides a comfortable seating solution for passengers of all ages. Tool-free attachment to the upper rack platform preserves the rack side rails for mounting additional accessories, such as pannier adapters. **For Globe Haul ST bike customers: Use of compatible (1) footrests (pegs), (2) passenger seat, (3) passenger handlebar, and (4) rear wheel cover required to safely carry passengers. All items available separately. ** - Designed for frictionless compatibility with the Haul ST and Haul LT - Reversible, asymmetric design allows for unlimited installation options. - Hook-and-loop strap attachment for fast and secure installation. - Up to 3 seats compatible with Haul LT.

The Ohlins Stumpjumper Spring sets a new benchmark for spring rate accuracy and light weight for steel springs. - Ultra-fine spring rates to ensure perfect set up for all weights. - Spring rates are broken down to 4 N/mm (23 lbs./in). - Fits Ohlins TTX shock absorber for Stumpjumper FSR only. - Made with proprietary ultra lightweight steel, it's incredible for keeping your build weight down for trail riding.

The new generation spring series features a race-ready weight with big mountain strength. You'll also find advanced technologies that feature a multi-step surface treatment process, as well as cutting-edge heat treatments. Lastly, we use wire materials that allow us to stress the wire harder, without causing damage to the spring, and therefore design lighter springs. - Precise spring rates are broken down to 4 N/mm (23 lbs./in).

The new generation spring series features a race-ready weight with big mountain strength. You'll also find advanced technologies that feature a multi-step surface treatment process, as well as cutting-edge heat treatments. Lastly, we use wire materials that allow us to stress the wire harder, without causing damage to the spring, and therefore design lighter springs. - Precise spring rates are broken down to 4 N/mm (23 lbs./in).

The Ohlins RXF 36 Coil Fork Spring sets a new benchmark for spring rate accuracy and light weight for trail and all-mountain fork springs. - Ultra-fine spring rates to ensure perfect set up for all weights. - Spring rates are broken down to 0.9 N/mm (5 lbs./in). - Fits Ohlins RXF Coil fork only.

Connects the Specialized SL Range Extender Battery with all of our Turbo SL off-road bikes. - Custom connector with lock-mechanism ensures a secure connection. - Length: 160mm

Connects the Specialized SL Range Extender Battery with all our Turbo SL on-road bikes. - Custom connector with lock-mechanism ensures a secure connection. - Length: 220mm

Developed to work on either the Specialized Carbon or Hydroformed Alloy Aerobar, the Shiv Low-Stack Clamp reduces up to 19mm of stack height, in order to obtain a lower position while in the Aerobars. - Compatible w/ Specialized Carbon or Hydroformed Alloy Aerobar (2102-2010 / 2102-2005) - Reduces 19mm (1.9cm) of stack height

Get the DownLow. Our DownLow dropper post is an infinitely adjustable, easily serviceable, air/hydraulic unit with a sweet cable remote. It goes up. It goes down. You need one. Where it thrives: Challenging trails, up and down hills What it's built for: Handling, confidence Highlights: - 31.6 diameter - Alloy construction with slot key bushings and wiper seals - Preset airspring for no-fuss setup

Crank Insurance compatible with HollowGram cranks. Features - Protects HollowGram crank arm from rock strikes - Reflective strip keeps riders visible